- Formulated for cultured marble, granite and onyx manufacturers.
- Blend of synthetic waxes, polymers and resins for high-heat stability and multiple releases.
- Brush or wipe on three consecutive coats of #626, one coat at a time allowing each coat to dry before reapplying second and third coat to all hats, flanges, corners, edges and areas where a gloss is not required. Do not wipe. This builds a wax surface that will produce multiple releases and should require only periodic application unless area is marred when pulling a part. In this case, reapply #626 Polymer Hat Wax to affected area.
-
-
- Can be mopped or wiped on. Reduces clean-up time and increases efficiency in production.
- Eliminates fire hazard by removing the use of paper.
- One gallon of #PB-1 will cover approximately 150-200 square feet on porous surface and up to 400 square feet on smooth non-porous surface.
- Recommend using three applications; Allow each coat to dry prior to applying the next coat – assuring proper coverage.cations; Allow each coat to dry prior to applying the next coat – assuring proper coverage.
-
- Formulated exclusively for the FRP, cultured marble and onyx manufacturers.
- Semi-viscous paste wax that may be brushed or wiped on.
- White in color so that it will not discolor.
- Also effective in release hats, flanges and back splashes.
-
- Synthetic, polymer resin based, low viscosity sealant that can be sprayed or wiped on the prepared mold.
- Highly recommended as a spray base mold release wax for all non-skid areas.
- Apply in the following manner:
- For High Shine: Spray on, allow it to dry and wipe off.
- For Dull Finish: Spray on, allow it to dry, wipe off surplus from only outside surfaces.
- On non-skid area, just apply but do not wipe.
-
- Formulated specifically for FRP and cultured marble industries where a flange- or edge-wax is required to assist in the prompt and easy release of the part.
- Edge Wax is a semi-paste and it incorporates synthetic waxes into a system that forms a film that is virtually unbendable when applied as follows.
-
- Made with a heavy wax base.
- Fine polishing compound used for the final machine polishing and dressing of molds before sealing and waxing.
- Improves clarity and luster.
- Excellent for older parts where light buffing may be required.
-
- A fine micro compound formulated to remove sandpaper marks and imperfections quickly and easily while leaving a high gloss and minimizing swirl problems.
- Easily removes 1500 grit sand marks with a 100% wool cutting pad and 2000 or finer grit with an aggressive foam pad.
- Can be applied to all painted or gel coat surfaces.
-
- Fast cutting compound that can be applied by hand or machine.
- Recommended for rubbing out fine mold imperfections and fine or minor scratches.
- Removes and blends or does touch up of mold surfaces when removal of foreign matter is essential.
- Can also be used in heavy-duty work.
-
- Specially formulated for removal of wet or dry sanding marks, imperfections and other mild defects without scouring the gel coat.
- A fast cutting compound formulated with fine abrasives and silicates to remove fine to medium scratches and blemishes.
- Can be used on all gel coated surfaces as well as other mold materials.
-
- FK’s premium cleaner that incorporates glazing and spreading agents.
- Cleans deeper without any heavy abrasive action.
- Easily relieves buffer swirls, paint and gel burns; Smoothens and removes fine scratches and blemishes.
- Assures a deeper and cleaner finish on molds for sharp looking parts.
- Recommended for rubbing out slight imperfections in the mold or finished parts and for removal of oxidation and/or discoloration of older parts. It is comparable to Meguire #1 Compound.
-
- Heavy-duty (HD) cousin of FK’s #332: Hand or Spray Interphase Release Wax. Contains the same high-melt synthetic blend waxes incorporated into #1000P: Hi-Low Paste Wax and #1000L: Hi-Low Liquid Wax but the solvent systems have been changed to reduce viscosity and make the product sprayable.
- Field tested and fully embraced by all users because it gets the job done – especially for larger molds, panels and other large jobs that require excessive labor for application of paste or liquid waxes.
- Very easy application – just spray on, allow it to dry and then wipe lightly – quick and easy. Cuts your labor costs and increases your productivity.
-
- Specially designed to reduce the slip factor, which under some situations might allude to pre-release.
- In the event “pre-release” occurs on corners, wells and radiuses due to excessive exothermic heat generated by mass chopping over these areas due to repeated passes, apply #1006 as the last coat or last two coats over the application of #1000P prior to gel coat and lay up.
