- Incorporates a blend of polyethylene resins, polymers and sun screening agents to form a protective barrier against exposure, inclement weather, heat, and ultraviolet solar rays.
- A protective coating without the extreme and difficult problems of removal that most products of this nature represent.
- Recommend use of either pressurized or siphon spray gun as an applicator. When spraying, do not to exceed gun pressure greater than 40 PSI. Adjust fan to desired width over a pre-cleaned surface. Spray one coat; allow it to dry. Cross spray, allow to dry. Spray flow coat to desired thickness for proper coverage.
-
-
- Synthetic, polymer resin based, low viscosity sealant that can be sprayed or wiped on the prepared mold.
- Highly recommended as a spray base mold release wax for all non-skid areas.
- Apply in the following manner:
- For High Shine: Spray on, allow it to dry and wipe off.
- For Dull Finish: Spray on, allow it to dry, wipe off surplus from only outside surfaces.
- On non-skid area, just apply but do not wipe.
-
- True high-gloss paste wax.
- Withstands high-temperature exothermic reactions of resins and does multiple releases easily.
- Contains carnauba wax, synthetic waxes and high-temperature resistant resins for effective multiple releases of plastic parts through numerous cycles.
- Good for up to 230º F or 110º C.
- Buttery texture provides easy on/off applications.
- Sets up faster and harder and assures quick, clean releases without wax buildup or transfer.
- Recommended for the effective release of any FRP or cultured marble parts, polyesters, polyurethane, etc....
-
- A water based dressing that is Body Shop safe.
- It is made thick for easy applicability using a sponge or a brush.
- Tires will be dark and glossy.
- # 350 will not wash off that easily and thus will last long.
- Some tires, which are very porous or cracked and dry, will require extra coat of dressing because some of the dressing will be absorbed.
-
- Cleans and waxes metal, glass and painted surfaces.
- Removes dust and finger prints.
- Leaves a bright, glossy shine.
- Eliminates the need for constant washing.
- Body Shop Safe.
- Safe as a clay lubricant.
- CA VOC Compliant
- Recommended for Exterior Use
-
- # 440-5 is a micro abrasive compound formulated for quick cutting power without scouring or tearing up the clear coat, leaving an exceptional high gloss finish.
- For removal of heavy oxidation, scratches and imperfections caused by fallout or other surface impediments.
- It is excellent for Body Shop use.
- Removes sanding marks 1000 grit or finer.
-
- Specially formulated for removal of wet or dry sanding marks, imperfections and other mild defects without scouring the gel coat.
- A fast cutting compound formulated with fine abrasives and silicates to remove fine to medium scratches and blemishes.
- Can be used on all gel coated surfaces as well as other mold materials.
-
Out of stock
- Fast cutting compound that can be applied by hand or machine.
- Recommended for rubbing out fine mold imperfections and fine or minor scratches.
- Removes and blends or does touch up of mold surfaces when removal of foreign matter is essential.
- Can also be used in heavy-duty work.
-
Out of stock
- Formulated exclusively for the FRP, cultured marble and onyx manufacturers.
- Semi-viscous paste wax that may be brushed or wiped on.
- White in color so that it will not discolor.
- Also effective in release hats, flanges and back splashes.
-
Out of stock
- Formulated for cultured marble, granite and onyx manufacturers.
- Blend of synthetic waxes, polymers and resins for high-heat stability and multiple releases.
- Brush or wipe on three consecutive coats of #626, one coat at a time allowing each coat to dry before reapplying second and third coat to all hats, flanges, corners, edges and areas where a gloss is not required. Do not wipe. This builds a wax surface that will produce multiple releases and should require only periodic application unless area is marred when pulling a part. In this case, reapply #626 Polymer Hat Wax to affected area.
-
Out of stock
- Formulated specifically for FRP and cultured marble industries where a flange- or edge-wax is required to assist in the prompt and easy release of the part.
- Edge Wax is a semi-paste and it incorporates synthetic waxes into a system that forms a film that is virtually unbendable when applied as follows.
-
- Specially formulated for the Fiberglass Reinforced Plastic (FRP) Industry to clean molds and relieve the problems of wax build-up & over-spray from mold surfaces.
- Important mold release components of Hi-Low Temp 1000 series waxes are specially blended in this product to liquefy and remove most waxes from the molds.
- Can also be used as an inter-phase item for the wax system for prolonged releases and as a cleaner for sharper molds and parts.
- Please note #69 mold cleaner does not relieve Styrene burns.
