Shop

Featured Products

View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#86: Seal Kote

$107.80 – $338.00
A polymer solution designed for efficient "sealing of porosity" in new and rejuvenated molds.

Aids and assists the wax release agents to assure a clean and easy demolding.
View Cart

Details Quick View

#135T: Polymer Release Agent
A polymer-based release agent which has high heat stability. It’s polymers provide multiple releases and protection from high heat generated from accelerated exothermic reactions. It is specially designed for:

Accelerated Exothermic Resins up to 400º F or 204º C

Multiple Releases

Compression Molding

Vacuum Bagging

Resin Transfer Molding (RTM)

NOTE: For best results, use terry cloth or Turkish towels when applying #135T. Apply in a circular motion to mold by overlapping previous area. Work product in thoroughly over the mold creating a thin even coat. Check for uniform coverage. Allow it to dry. Reapply as directed. #135T may be sprayed. When applying, if sprayed, we suggest wiping it lightly over sprayed film for uniform coverage.
View Cart

Details Quick View

#80: Liquid Mold Cleaner
Same usage as #135-80, but #80 is milder and contains no toluene or polymers.

Specially formulated for cleaning Elastomer Resins (ER).

Contains special surfactants that do not react with the resin that other cleaners might.

Browse all products

View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#2685: Cherry Pink Paste Wax

$18.75 – $197.16

Finish Kare’s 2685 Cherry Pink Paste Wax is a special blend of wax and polymer resins. This delightfully scented, buttery soft wax is easy to apply. It is equally as effortless to wipe off and produces a deep glossy protective film that lasts for 3-6 months. It is safe to use for all Automotive, Marine, Motorcycle and Aircraft finishes.
Out of stock

View Cart

Details Quick View

#923: Micro Polishing Compound
A fine micro compound formulated to remove sandpaper marks and imperfections quickly and easily while leaving a high gloss and minimizing swirl problems.

Easily removes 1500 grit sand marks with a 100% wool cutting pad and 2000 or finer grit with an aggressive foam pad.

Can be applied to all painted or gel coat surfaces.
View Cart

Details Quick View

#330: Mini Buff
Made with a heavy wax base.

Fine polishing compound used for the final machine polishing and dressing of molds before sealing and waxing.

Improves clarity and luster.

Excellent for older parts where light buffing may be required.
Out of stock

View Cart

Details Quick View

#626: Polymer Hat Wax
Formulated for cultured marble, granite and onyx manufacturers.

Blend of synthetic waxes, polymers and resins for high-heat stability and multiple releases.

Brush or wipe on three consecutive coats of #626, one coat at a time allowing each coat to dry before reapplying second and third coat to all hats, flanges, corners, edges and areas where a gloss is not required. Do not wipe. This builds a wax surface that will produce multiple releases and should require only periodic application unless area is marred when pulling a part. In this case, reapply #626 Polymer Hat Wax to affected area.

NOTE: On some molds Polymer Hat Wax acts as a transfer wax, whereby it will be removed with the first, second or third pull and will leave a bright shine on the mold. This shows that the polymer resin has fused to the mold and it will allow several additional releases without reapplication. As the mold dulls down or the part pulls hard, reapply and continue cycle. IMPORTANT: When changing products, or periodically as a mold maintenance program, you need to clean the molds. This reduces resin transfer, wax build-up, hazing, etc... FK has developed a special polymer mold cleaner, #135-80 for this purpose. It will deter build-up of wax and styrene resin and will assure longer mold use with continuous releases. #135-80, Polymer Mold Cleaner inclusively forms a film on the mold that deters build-up, and extends the use of #626 by giving additional releases, thus reducing costs.
View Cart

Details Quick View

#331-21: Storage Wax
Incorporates a blend of polyethylene resins, polymers and sun screening agents to form a protective barrier against exposure, inclement weather, heat, and ultraviolet solar rays.

A protective coating without the extreme and difficult problems of removal that most products of this nature represent.

Recommend use of either pressurized or siphon spray gun as an applicator. When spraying, do not to exceed gun pressure greater than 40 PSI. Adjust fan to desired width over a pre-cleaned surface. Spray one coat; allow it to dry. Cross spray, allow to dry. Spray flow coat to desired thickness for proper coverage.

REMOVAL: On molds that have been exposed to weather conditions and have become coated with dirt, dust or grit, hose off entire mold to remove debris prior to washing and wiping. Wipe with cloth or wash with simple soap solution under agitation. In extreme cases, wipe down with with FK’s #69: Mold Cleaner & Stripper to remove the wax. Re-wax the mold by reapplying one or two coats of wax release agents and then place it back into production.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#PB-1: Traffic wax

$88.00 – $280.00
Can be mopped or wiped on. Reduces clean-up time and increases efficiency in production.

Eliminates fire hazard by removing the use of paper.

One gallon of #PB-1 will cover approximately 150-200 square feet on porous surface and up to 400 square feet on smooth non-porous surface.

Recommend using three applications; Allow each coat to dry prior to applying the next coat – assuring proper coverage.cations; Allow each coat to dry prior to applying the next coat – assuring proper coverage.
Out of stock

View Cart

Details Quick View

#604B: Mold Sealer & Release Agent
Formulated exclusively for the FRP, cultured marble and onyx manufacturers.

Semi-viscous paste wax that may be brushed or wiped on.

White in color so that it will not discolor.

Also effective in release hats, flanges and back splashes.

DIRECTIONS: Apply three consecutive coats of #604B with a brush, cloth or sponge, one coat at a time. Allow each coat to dry before applying second and third coats to all flanges, hats and back splashes where gloss is not required. This builds up a wax surface that will produce multiple releases and should require only periodic application unless area is marred when demolding. In this case, reapply #604B to the affected area(s).
View Cart

Details Quick View

#332: Hand or Spray Interphase Release Wax
Synthetic, polymer resin based, low viscosity sealant that can be sprayed or wiped on the prepared mold.

Highly recommended as a spray base mold release wax for all non-skid areas.

Apply in the following manner:

For High Shine: Spray on, allow it to dry and wipe off.

For Dull Finish: Spray on, allow it to dry, wipe off surplus from only outside surfaces.

On non-skid area, just apply but do not wipe.

NOTE: This product should only be used in this manner after at least one part is demolded with FK's Paste Wax.
Out of stock

View Cart

Details Quick View

#68: Edge Wax
Formulated specifically for FRP and cultured marble industries where a flange- or edge-wax is required to assist in the prompt and easy release of the part.

Edge Wax is a semi-paste and it incorporates synthetic waxes into a system that forms a film that is virtually unbendable when applied as follows.

DIRECTIONS: Apply 3 consecutive coats of #68 Edge Wax. Allow each coat to dry before applying the next one. Apply 2nd and 3rd coats to all flanges, corners, edges and areas where a gloss is not required. This builds up a wax surface that will produce multiple releases and should only require periodic application unless the area is marred when pulling the part. Reapply the Edge Wax to affected areas and a thin coat all over to get an even film.
View Cart

Details Quick View

#145: Poly Wipe Liquid Sealant
Contains exclusive Anti-static agents.

It is a water based resin wax system for removing surface soil while providing a lustrous protected surface.

A quick finish rejuvenator for all fiberglass and painted surfaces.

Seals and protects.

DIRECTIONS: Spray on, wipe off. Available in Qts - 32 ozs.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

BWM 101: Hi-Temp Paste Wax

$21.30 – $205.32
FINAL STEP OF 3 STEP BIG WHITE PASTE WAX SYSTEM FK’s # BWM 101 is made from a blend of synthetic waxes to obtain a high degree of consistent quality. The most important attributes of this wax blend are hi melting points and greater hardness than natural waxes. The resulting film provides not only the high gloss but resistance to wear from heat, water & other natural causes. California VOC compliant. It is easy to use and easy to wipe off. It is fantastic for the following Marine, Aircraft & Automotive finishes:

Clear Coats

Gel Coats

Painted Surfaces

Chrom

Stainless Steel

Fiberglass

* Not suited for Plastic trim DIRECTIONS: Apply BWM 101 with a clean & soft cloth onto an already clean surface in an overlapping circular pattern for a uniform film. Allow to dry and wipe off residue with a soft cloth. Then buff to a bright, hard, slick and protective finish. *** BWM 101 used to be known as BWM-1000P, but due to the confusion with our 1000P Mold Release product, the name was changed.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

BWM 164: Sealant Conditioner

$21.00 – $272.00

BWM-164 is designed for all fiberglass, chrome & painted surfaces. It brings back dull surfaces to new or near new condition. It is a polish & conditioner in one, so it cleans, protects and restores in one easy step. If there is excessive oxidation, a second application may be necessary. California VOC compliant. DIRECTIONS: It can be applied by hand or machine. For hand use, apply # 164 with a soft towel by working it thoroughly into the surface. Use overlapping circular motion for uniform coverage. Allow it to dry to a haze and wipe off residue with a soft cloth, turn to a clean side of a towel & buff to a glossy smooth surface. When using a buffer maintain a light even pressure and buff in overlapping areas for uniformity. Then, allow it to dry completely and wipe with a clean soft cloth or towel to a glossy surface.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

BWM 114: Rubbing Compound

$20.00 – $356.40

BWM 114 is a fast cutting compound for all fiberglass, chrome, and paint, buffered for effective cleaning without heavy scratching. It is STEP 1 of 3 in our BIG WHITE PASTE WAX SYSTEM. Apply to all fiberglass, chrome and painted surfaces to remove oxidation, rust or stains. Follow with an application of BWM # 164 Sealant Conditioner for smoothing and color brightening. Then BWM for the ultimate in surface protection, apply BWM # 101 Hi-Temp Paste Wax. DIRECTIONS: Apply compound with soft toweling. Work thoroughly into the surface to be cleaned and waxed. Use circular motion. Overlap previous area for uniformity, wipe off residue with soft cloth or toweling. Turn to clean side. Buff to a bright slick surface. Machine Operation: Power Buff. Dab material with the brush and apply on to the area to be buffed. Spread evenly, maintaining a light even pressure. Continue to buff, overlapping previous area for uniformity. Finish buff to dry lustrous finish.
View Cart

Details Quick View

#303: Foam Pad Glaze
Recommended for use to remove finer scratches and compound swirl marks from all types of painted finishes.

DIRECTIONS: Shake well and do not apply in direct sun or on extremely hot surfaces. On area to be buffed make thin stripe of #303 approximately 6 inches apart then spread the product evenly with light even pressure. Buff at about 1500 rpm. Then reduce the speed to about 1000 rpm and buff the surface to a high gloss. Check for clarity, swirls & scratches. If surface is clear, repeat the process on next section. Overlap area for continuity.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#300: Hand Glaze

$15.60
Formulated for use by hand, to produce a wet look shine on all paint finishes after machine glazing.

This special blend with high melt Polymers and Resins will provide long lasting gloss and protection.

Contains no harmful silicones and allows fresh paint to breath and dry properly.

DIRECTIONS: Shake well and do not apply in direct sunlight or extremely hot surfaces. Apply a small amount onto a soft clean applicator. Work well into surface using light even pressure. Apply evenly to entire panel, then with a clean soft Finish Kare micro fiber towel, wipe product to a high luster.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#2180: Ultra Polymer Sealant

$30.00 – $98.00
A polymer sealant for all finishes. It is a blend of anti-corrosive, detergent-resistant polysiloxane copolymers and high melt resins that provides a high gloss, durable protective film that protects the finish against heat, water, and detergent.

Removes surface accumulation and oxidation.

Penetrates and seals giving great depth to true paint colors thus it provides months of maintenance free appearance and protection against environmental elements, oxidation and detergents.

To protect the finish of your car for a long time, FK recommends the use of # 2180 once a month initially and then once every 2-3 months.

Not safe to use on Trims.

DIRECTIONS: Do not apply in direct sun or on hot surfaces. Use soft towel or microfiber cloth for application and wiping. Apply the product and work it well into the finish. Allow it to dry, then wipe to brilliant & long-lasting luster. In case of excessive dirt or grit, wash the surface with mild soap before applying.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#218: Poly Wipe Sealant Conditioner

$16.20
Poly Wipe is a polymer sealant.

Apply it as a final protective coat over all new or pre-cleaned, different color finishes.

Easy on and off application.

DIRECTIONS: Shake well. Do not apply in direct sun or on hot surfaces. Apply to clean surfaces only. For best results, apply using a soft towel or an orbital buffer with a soft terry cloth bonnet working the material well into the finish. Allow the product to dry completely, normally about 15 minutes. Remove it with a soft, dry towel. Poly Wipe may be applied to any OEM Paint system and it is compatible with all new Poly Urethane and Urethane systems. Please allow 24 hours cure time of the paint system before applying Poly Wipe. Note: The product should not be applied to old style enamels and lacquers until all the solvents have evaporated, normally in 30 to 45 days.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#215: One Step Cleaner Sealant

$14.30
# 215 is formulated for high production reconditioning.

This polymer Cleaner Sealant can be used by hand or machine to remove oxidation, light scratches and blemishes and to restore a paint to a deep gloss with a durable finish.

DIRECTIONS: For hand application apply it in a circular motion with a soft applicator pad and overlap the areas. Work it in thoroughly and create a thin even film on the surface. Allow to haze and then wipe off with a soft micro fiber towel to a rich deep gloss. To remove oxidation and light surface scratches use a buffer with a yellow foam pad. For heavier scratches and oxidation use white cutting wool pad. Buffer speed should be about 1500 rpm initially then reduce it to about 1000 rpm and use black finishing pad to remove finer scratches and swirl marks to get a deep gloss.
View Cart

Details Quick View

#350: Super Polymer Tire Dressing
A water based dressing that is Body Shop safe.

It is made thick for easy applicability using a sponge or a brush.

Tires will be dark and glossy.

# 350 will not wash off that easily and thus will last long.

Some tires, which are very porous or cracked and dry, will require extra coat of dressing because some of the dressing will be absorbed.

DIRECTIONS: Shake Well. For best results use it as is on a clean dry surface. We recommend to use sponge for easy applicability. Allow it to dry for about 10 minutes and then wipe lightly. To avoid sling-off please wipe the excess.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#108: Top Kote Tire Dressing

$16.60 – $48.20
A liquid polymer sealant conditioner formulated to condition, restore and protect leather surfaces and all interior/exterior plastic, rubber and vinyl surfaces.

It leaves a like new finish that is not greasy or wet.

Excellent for use on leather interiors, dashes, engine compartments, tires, rubber trim and molding.

#180AS is enriched with an anti-static agent to eliminate dust attraction.

DIRECTIONS: Use as is. Do not apply on suede. Spray or wipe on using 100% terry cloth towel or soft applicator pad. Allow it to dry, wipe surplus material slightly.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#146AS: Anti-Static Finish Restorer

$14.00
A blend of poly resins, synthetic and organic waxes with anti static agent that eliminates static dust cling.

Brightens and shines while cleaning finger print marks and surface dust.

Easy to use and sprays well.

It is recommended to be used at new car dealer show rooms for quick clean and excellent shine.

DIRECTION: Shake Well. Use as is. Do not apply in direct sun or on hot surfaces. Wipe or mist on with a sprayer & spread using a damp cloth evenly over the surface. Do one section at a time. Do not allow it to dry. Wipe with soft absorbent cloth. Re-Wipe with a dry, soft cloth to get a clear bright luster. Use of micro fiber for spreading & wiping is highly recommended.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#425: Extra Slick Final Body Shine

$16.00 – $30.00
Cleans and waxes metal, glass and painted surfaces.

Removes dust and finger prints.

Leaves a bright, glossy shine.

Eliminates the need for constant washing.

Body Shop Safe.

Safe as a clay lubricant.

CA VOC Compliant

Recommended for Exterior Use

DIRECTIONS: Use as is. Simply spray Finish Kare’s Final Body Shine on a dusty, smudged or fingerprinted surface. Then wipe with a clean microfiber towel to get a deep protective shine. It is that easy. * Safe to use on Plastic & Rubber Trim
Out of stock

View Cart

Details Quick View

817: Sparkle Plenty

$23.00 – $90.00

A strong de-limonene based degreaser.
Out of stock

View Cart

Details Quick View

118SC: Super Concentrated Shampoo

$27.00 – $98.00

An innovative wash that was engineered to be pH neutral, gentle for all finishes, 100% clean rinsing while delivering real cleaning power. With a plus factor this premium wash softens hard wash water and neutralizes acid rain. Biodegradable formula safely and effectively removes dirt and grime without striping waxes or sealants. Leaves a clean high gloss finish. Excellent for use on cars, boats, aircraft and rv’s.
Out of stock

View Cart

Details Quick View

#121: Ultimate Interior Cleaner

$29.10 – $84.60

# 121 Ultimate Cleaner is just that "The Ultimate Cleaner". Properly diluted # 121 is a safe effective pH neutral cleaner for most all surfaces including interior carpets, vinyl, rubber, leather, tires, engine compartments, door jams, aircraft underbelly cleaning etc. Formulated with antibacterial agents it kills the bacteria that creates odor leaving a clean fresh sent. It is also excellent for home. Use to clean counters,tubs, floors, stone, spot clean clothing prior to washing and tuff carpet stains.
Out of stock

View Cart

Details Quick View

#1016: Poly-Wash & Wax Concentrate

$37.80 – $118.70
The ultimate wash adified amides, enhanced by the presence of fatty based amide derivatives.

Cationic in nature 1016 generates a clear glossy protective film that attaches itself to finish while delivering a noticeable enhanced finish.

The finish glistens without the use of waxes or oils. Excellent for use on paint, glassnd wax with real high tech polymer protection unlike any other product.

Engineered from mo, chrome, gel coat, fiberglass and Plexiglas etc.
View Cart

Details Quick View

#440-5: Polishing Compound
# 440-5 is a micro abrasive compound formulated for quick cutting power without scouring or tearing up the clear coat, leaving an exceptional high gloss finish.

For removal of heavy oxidation, scratches and imperfections caused by fallout or other surface impediments.

It is excellent for Body Shop use.

Removes sanding marks 1000 grit or finer.

DIRECTIONS: Shake well. Do not apply in direct sunlight or ectremely hot surfaces. Using a wool cutting pad, set buffer at 1800-2000 rpm. Apply enough product to create a buffing film that will act as a lubricant between the pad and the painted surface. DO NOT DRY BUFF. Begin buffing using a medium pressure at first them lighten up, overlapping and spreading product evenly over a controlled section. NOTE: For best results, maintain a wet buffing film, avoid dry buffing and tilting pad on edge.
View Cart

Details Quick View

#115L-4: Heavy Duty Liquid Compound
Is a fast cutting compound and can be used by hand or machine.

It is recommended for rubbing out major and fine mold imperfections, all kinds of scratches, over-spray and removal of foreign matter.

It is designed for medium to heavy duty work.

DIRECTIONS: To remove oxidation and light surface scratches use a rotary buffer with yellow foam pad or for heavier scratches and oxidation use a white wool pad. Set buffer speed at about 1500 rpm. Apply enough 115L-4 to buff a 2’x2’ section. Apply light even pressure in overlapping manner as you buff. DO NOT OVERHEAT. Wipe away any splatter with a soft clean towel then continue onto next section. After oxidation and blemishes have been removed, inspect the area for swirls. If you see swirls, switch to a black finishing foam pad and lower buffing speed to 1000rpm. Apply light even pressure & keep pad flat to surface whenever possible doing a 2’x2’ section at a time. Continue in this manner until all swirls are eliminated.
View Cart

Details Quick View

#330: Mini Buff
Made with a heavy wax base.

Fine polishing compound used for the final machine polishing and dressing of molds before sealing and waxing.

Improves clarity and luster.

Excellent for older parts where light buffing may be required.
Out of stock

View Cart

Details Quick View

#923: Micro Polishing Compound
A fine micro compound formulated to remove sandpaper marks and imperfections quickly and easily while leaving a high gloss and minimizing swirl problems.

Easily removes 1500 grit sand marks with a 100% wool cutting pad and 2000 or finer grit with an aggressive foam pad.

Can be applied to all painted or gel coat surfaces.
Out of stock

View Cart

Details Quick View

#600: White Fine Rubbing Compound (Paste)
Fast cutting compound that can be applied by hand or machine.

Recommended for rubbing out fine mold imperfections and fine or minor scratches.

Removes and blends or does touch up of mold surfaces when removal of foreign matter is essential.

Can also be used in heavy-duty work.
View Cart

Details Quick View

#440-5: Polishing Compound
Specially formulated for removal of wet or dry sanding marks, imperfections and other mild defects without scouring the gel coat.

A fast cutting compound formulated with fine abrasives and silicates to remove fine to medium scratches and blemishes.

Can be used on all gel coated surfaces as well as other mold materials.
View Cart

Details Quick View

#103: Extra Heavy Duty Cleaner
FK’s premium cleaner that incorporates glazing and spreading agents.

Cleans deeper without any heavy abrasive action.

Easily relieves buffer swirls, paint and gel burns; Smoothens and removes fine scratches and blemishes.

Assures a deeper and cleaner finish on molds for sharp looking parts.

Recommended for rubbing out slight imperfections in the mold or finished parts and for removal of oxidation and/or discoloration of older parts. It is comparable to Meguire #1 Compound.
View Cart

Details Quick View

#1000L-28: Sprayable HD Mold Release Wax
Heavy-duty (HD) cousin of FK’s #332: Hand or Spray Interphase Release Wax. Contains the same high-melt synthetic blend waxes incorporated into #1000P: Hi-Low Paste Wax and #1000L: Hi-Low Liquid Wax but the solvent systems have been changed to reduce viscosity and make the product sprayable.

Field tested and fully embraced by all users because it gets the job done – especially for larger molds, panels and other large jobs that require excessive labor for application of paste or liquid waxes.

Very easy application – just spray on, allow it to dry and then wipe lightly – quick and easy. Cuts your labor costs and increases your productivity.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#1006: Pre-Release Deterrent Paste Wax

$18.55 – $202.80
Specially designed to reduce the slip factor, which under some situations might allude to pre-release.

In the event “pre-release” occurs on corners, wells and radiuses due to excessive exothermic heat generated by mass chopping over these areas due to repeated passes, apply #1006 as the last coat or last two coats over the application of #1000P prior to gel coat and lay up.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#1000L: Hi-Low Liquid Wax

$92.00 – $291.00
Specially designed for use between multiple releases to relieve the wax build up and reduce surface tension in molds.

Helps to prolong the life of multiple cycle releases.

Solvents in the product liquefy the mold release waxes to form an even coat on the mold for easy de-molding.

Check out our other Wax Based Releases for all your release needs
Out of stock

View Cart

Details Quick View

#888: Max Mold Release Paste Wax
Similar in hardness to #1000P. It is yellow in color and has a peculiar, turpentine smell.

Comparable to Meguiar’s #8. Our extensive testing shows that you get equivalent or better release with #888 than with comparable Meguiar’s product.

Good for up to 230º F or 120º C.

This is one of our newer products and sample requests welcome.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#1000P: Hi-Low Paste Wax

$20.50 – $228.00
Contains a blend of synthetic waxes and is one of FK’s premium mold release waxes.

Proper application of this wax will result in a film that has high gloss and has resistance to intensive wear, heat and water.

Good for up to 275º F or 135º C.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#1004-23: Gel Coat Release Paste Wax

$17.50 – $202.00
Formulated so as to be brushed over gel coat before the final wax coat is applied without worrying about fish eye.

Recommended to be applied to any mold surface, whole or partial, where brushing the gel coat on the mold is required.

Can be used over #1000P as the final coat or used by itself when gel coating.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#1165: Hi-Temp Extra Hard Premium Wax

$19.50 – $216.00
As the name implies, designed to withstand higher temperatures and is harder than other waxes.

Good for up to 275º F or 135º C.

USAGE: Higher temperature exothermic reactions.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#333MR: Blue Wax

$19.75 – $219.00
True high-gloss paste wax.

Withstands high-temperature exothermic reactions of resins and does multiple releases easily.

Contains carnauba wax, synthetic waxes and high-temperature resistant resins for effective multiple releases of plastic parts through numerous cycles.

Good for up to 230º F or 110º C.

Buttery texture provides easy on/off applications.

Sets up faster and harder and assures quick, clean releases without wax buildup or transfer.

Recommended for the effective release of any FRP or cultured marble parts, polyesters, polyurethane, etc....

*** New 11 oz. can coming in 2023 to specific distributors***
View Cart

Details Quick View

#135ER: Polymer Release Agent for Urethane
It is recommended for the following types of urethane moldings:

Elastomer Urethane

Polyisocynate Component A

Hydro-Resin Component B

Urethane Foam

Isocynate Component A (Diphenylmethone)

Poly Component B (Polypreponal Glycol)

Note: For #135 ER, follow the same guidelines as #135T.
View Cart

Details Quick View

#135T: Polymer Release Agent
A polymer-based release agent which has high heat stability. It’s polymers provide multiple releases and protection from high heat generated from accelerated exothermic reactions. It is specially designed for:

Accelerated Exothermic Resins up to 400º F or 204º C

Multiple Releases

Compression Molding

Vacuum Bagging

Resin Transfer Molding (RTM)

NOTE: For best results, use terry cloth or Turkish towels when applying #135T. Apply in a circular motion to mold by overlapping previous area. Work product in thoroughly over the mold creating a thin even coat. Check for uniform coverage. Allow it to dry. Reapply as directed. #135T may be sprayed. When applying, if sprayed, we suggest wiping it lightly over sprayed film for uniform coverage.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#86: Seal Kote

$107.80 – $338.00
A polymer solution designed for efficient "sealing of porosity" in new and rejuvenated molds.

Aids and assists the wax release agents to assure a clean and easy demolding.
View Cart

Details Quick View

#80: Liquid Mold Cleaner
Same usage as #135-80, but #80 is milder and contains no toluene or polymers.

Specially formulated for cleaning Elastomer Resins (ER).

Contains special surfactants that do not react with the resin that other cleaners might.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#135-80: Polymer Mold Cleaner & Wax Remover

$94.20 – $345.00
Solvent-based mold cleaner for removing wax.

Contains toluene and fortified with polymers.

A much stronger cleaner than #69 that can be used for the clean-up of all types of molds prior to applying porosity sealing agents and mold release agents – wax-based or otherwise.

Apply at least 2 coats of #135-80 for proper cleaning of molds and assured releases.
View Cart

Details Quick View

#69AS: Anti-Static Mold Cleaner & Stripper
Same as #69 but contains anti-static agent which helps to reduce dust and particle attraction to molds due to buildup of static charge.

Specially formulated for the Fiberglass Reinforced Plastic (FRP) Industry to clean molds and relieve the problems of wax build-up & over-spray from mold surfaces.

Important mold release components of Hi-Low Temp 1000 series waxes are specially blended in this product to liquefy and remove most waxes from the molds.

Can also be used as an inter-phase item for the wax system for prolonged releases and as a cleaner for sharper molds and parts.

Please note #69AS does not relieve Styrene burns.
View Cart

Select options This product has multiple variants. The options may be chosen on the product page / Details Quick View

#69: Mold Cleaner & Stripper

$88.00 – $316.00
Specially formulated for the Fiberglass Reinforced Plastic (FRP) Industry to clean molds and relieve the problems of wax build-up & over-spray from mold surfaces.

Important mold release components of Hi-Low Temp 1000 series waxes are specially blended in this product to liquefy and remove most waxes from the molds.

Can also be used as an inter-phase item for the wax system for prolonged releases and as a cleaner for sharper molds and parts.

Please note #69 mold cleaner does not relieve Styrene burns.