- Specially designed for use between multiple releases to relieve the wax build up and reduce surface tension in molds.
- Helps to prolong the life of multiple cycle releases.
- Solvents in the product liquefy the mold release waxes to form an even coat on the mold for easy de-molding.
-
-
- Heavy-duty (HD) cousin of FK’s #332: Hand or Spray Interphase Release Wax. Contains the same high-melt synthetic blend waxes incorporated into #1000P: Hi-Low Paste Wax and #1000L: Hi-Low Liquid Wax but the solvent systems have been changed to reduce viscosity and make the product sprayable.
- Field tested and fully embraced by all users because it gets the job done – especially for larger molds, panels and other large jobs that require excessive labor for application of paste or liquid waxes.
- Very easy application – just spray on, allow it to dry and then wipe lightly – quick and easy. Cuts your labor costs and increases your productivity.
-
- Contains a blend of synthetic waxes and is one of FK’s premium mold release waxes.
- Proper application of this wax will result in a film that has high gloss and has resistance to intensive wear, heat and water.
- Good for up to 275º F or 135º C.
-
- Formulated so as to be brushed over gel coat before the final wax coat is applied without worrying about fish eye.
- Recommended to be applied to any mold surface, whole or partial, where brushing the gel coat on the mold is required.
- Can be used over #1000P as the final coat or used by itself when gel coating.
-
- Specially designed to reduce the slip factor, which under some situations might allude to pre-release.
- In the event “pre-release” occurs on corners, wells and radiuses due to excessive exothermic heat generated by mass chopping over these areas due to repeated passes, apply #1006 as the last coat or last two coats over the application of #1000P prior to gel coat and lay up.
-
- FK’s premium cleaner that incorporates glazing and spreading agents.
- Cleans deeper without any heavy abrasive action.
- Easily relieves buffer swirls, paint and gel burns; Smoothens and removes fine scratches and blemishes.
- Assures a deeper and cleaner finish on molds for sharp looking parts.
- Recommended for rubbing out slight imperfections in the mold or finished parts and for removal of oxidation and/or discoloration of older parts. It is comparable to Meguire #1 Compound.
-
- As the name implies, designed to withstand higher temperatures and is harder than other waxes.
- Good for up to 275º F or 135º C.
- USAGE: Higher temperature exothermic reactions.
-
It is recommended for the following types of urethane moldings:
- Elastomer Urethane
- Polyisocynate Component A
- Hydro-Resin Component B
- Urethane Foam
- Isocynate Component A (Diphenylmethone)
- Poly Component B (Polypreponal Glycol)
-
A polymer-based release agent which has high heat stability. It’s polymers provide multiple releases and protection from high heat generated from accelerated exothermic reactions. It is specially designed for:
- Accelerated Exothermic Resins up to 400º F or 204º C
- Multiple Releases
- Compression Molding
- Vacuum Bagging
- Resin Transfer Molding (RTM)
-
- Made with a heavy wax base.
- Fine polishing compound used for the final machine polishing and dressing of molds before sealing and waxing.
- Improves clarity and luster.
- Excellent for older parts where light buffing may be required.
-
- Synthetic, polymer resin based, low viscosity sealant that can be sprayed or wiped on the prepared mold.
- Highly recommended as a spray base mold release wax for all non-skid areas.
- Apply in the following manner:
- For High Shine: Spray on, allow it to dry and wipe off.
- For Dull Finish: Spray on, allow it to dry, wipe off surplus from only outside surfaces.
- On non-skid area, just apply but do not wipe.
-
- True high-gloss paste wax.
- Withstands high-temperature exothermic reactions of resins and does multiple releases easily.
- Contains carnauba wax, synthetic waxes and high-temperature resistant resins for effective multiple releases of plastic parts through numerous cycles.
- Good for up to 230º F or 110º C.
- Buttery texture provides easy on/off applications.
- Sets up faster and harder and assures quick, clean releases without wax buildup or transfer.
- Recommended for the effective release of any FRP or cultured marble parts, polyesters, polyurethane, etc....
