- Can be mopped or wiped on. Reduces clean-up time and increases efficiency in production.
- Eliminates fire hazard by removing the use of paper.
- One gallon of #PB-1 will cover approximately 150-200 square feet on porous surface and up to 400 square feet on smooth non-porous surface.
- Recommend using three applications; Allow each coat to dry prior to applying the next coat – assuring proper coverage.cations; Allow each coat to dry prior to applying the next coat – assuring proper coverage.
-
-
- A fine micro compound formulated to remove sandpaper marks and imperfections quickly and easily while leaving a high gloss and minimizing swirl problems.
- Easily removes 1500 grit sand marks with a 100% wool cutting pad and 2000 or finer grit with an aggressive foam pad.
- Can be applied to all painted or gel coat surfaces.
-
- Similar in hardness to #1000P. It is yellow in color and has a peculiar, turpentine smell.
- Comparable to Meguiar’s #8. Our extensive testing shows that you get equivalent or better release with #888 than with comparable Meguiar’s product.
- Good for up to 230º F or 120º C.
- This is one of our newer products and sample requests welcome.
-
- A polymer solution designed for efficient "sealing of porosity" in new and rejuvenated molds.
- Aids and assists the wax release agents to assure a clean and easy demolding.
-
- Solvent-based mold cleaner for removing wax.
- Contains toluene and fortified with polymers.
- A much stronger cleaner than #69 that can be used for the clean-up of all types of molds prior to applying porosity sealing agents and mold release agents – wax-based or otherwise.
- Apply at least 2 coats of #135-80 for proper cleaning of molds and assured releases.
-
- Same usage as #135-80, but #80 is milder and contains no toluene or polymers.
- Specially formulated for cleaning Elastomer Resins (ER).
- Contains special surfactants that do not react with the resin that other cleaners might.
-
- Same as #69 but contains anti-static agent which helps to reduce dust and particle attraction to molds due to buildup of static charge.
- Specially formulated for the Fiberglass Reinforced Plastic (FRP) Industry to clean molds and relieve the problems of wax build-up & over-spray from mold surfaces.
- Important mold release components of Hi-Low Temp 1000 series waxes are specially blended in this product to liquefy and remove most waxes from the molds.
- Can also be used as an inter-phase item for the wax system for prolonged releases and as a cleaner for sharper molds and parts.
- Please note #69AS does not relieve Styrene burns.
-
- Specially formulated for the Fiberglass Reinforced Plastic (FRP) Industry to clean molds and relieve the problems of wax build-up & over-spray from mold surfaces.
- Important mold release components of Hi-Low Temp 1000 series waxes are specially blended in this product to liquefy and remove most waxes from the molds.
- Can also be used as an inter-phase item for the wax system for prolonged releases and as a cleaner for sharper molds and parts.
- Please note #69 mold cleaner does not relieve Styrene burns.
-
- Formulated specifically for FRP and cultured marble industries where a flange- or edge-wax is required to assist in the prompt and easy release of the part.
- Edge Wax is a semi-paste and it incorporates synthetic waxes into a system that forms a film that is virtually unbendable when applied as follows.
-
- Formulated for cultured marble, granite and onyx manufacturers.
- Blend of synthetic waxes, polymers and resins for high-heat stability and multiple releases.
- Brush or wipe on three consecutive coats of #626, one coat at a time allowing each coat to dry before reapplying second and third coat to all hats, flanges, corners, edges and areas where a gloss is not required. Do not wipe. This builds a wax surface that will produce multiple releases and should require only periodic application unless area is marred when pulling a part. In this case, reapply #626 Polymer Hat Wax to affected area.
-
- Formulated exclusively for the FRP, cultured marble and onyx manufacturers.
- Semi-viscous paste wax that may be brushed or wiped on.
- White in color so that it will not discolor.
- Also effective in release hats, flanges and back splashes.
-
- Fast cutting compound that can be applied by hand or machine.
- Recommended for rubbing out fine mold imperfections and fine or minor scratches.
- Removes and blends or does touch up of mold surfaces when removal of foreign matter is essential.
- Can also be used in heavy-duty work.